diff options
Diffstat (limited to 'test/Adafruit_PN532.h')
| -rw-r--r-- | test/Adafruit_PN532.h | 223 |
1 files changed, 0 insertions, 223 deletions
diff --git a/test/Adafruit_PN532.h b/test/Adafruit_PN532.h deleted file mode 100644 index 6fcb053..0000000 --- a/test/Adafruit_PN532.h +++ /dev/null @@ -1,223 +0,0 @@ -/**************************************************************************/ -/*! - @file Adafruit_PN532.h - - v2.0 - Refactored to add I2C support from Adafruit_NFCShield_I2C library. - - v1.1 - Added full command list - - Added 'verbose' mode flag to constructor to toggle debug output - - Changed readPassiveTargetID() to return variable length values -*/ -/**************************************************************************/ - -#ifndef ADAFRUIT_PN532_H -#define ADAFRUIT_PN532_H - -#include "Arduino.h" - -#include <Adafruit_I2CDevice.h> -#include <Adafruit_SPIDevice.h> - -#define PN532_PREAMBLE (0x00) ///< Command sequence start, byte 1/3 -#define PN532_STARTCODE1 (0x00) ///< Command sequence start, byte 2/3 -#define PN532_STARTCODE2 (0xFF) ///< Command sequence start, byte 3/3 -#define PN532_POSTAMBLE (0x00) ///< EOD - -#define PN532_HOSTTOPN532 (0xD4) ///< Host-to-PN532 -#define PN532_PN532TOHOST (0xD5) ///< PN532-to-host - -// PN532 Commands -#define PN532_COMMAND_DIAGNOSE (0x00) ///< Diagnose -#define PN532_COMMAND_GETFIRMWAREVERSION (0x02) ///< Get firmware version -#define PN532_COMMAND_GETGENERALSTATUS (0x04) ///< Get general status -#define PN532_COMMAND_READREGISTER (0x06) ///< Read register -#define PN532_COMMAND_WRITEREGISTER (0x08) ///< Write register -#define PN532_COMMAND_READGPIO (0x0C) ///< Read GPIO -#define PN532_COMMAND_WRITEGPIO (0x0E) ///< Write GPIO -#define PN532_COMMAND_SETSERIALBAUDRATE (0x10) ///< Set serial baud rate -#define PN532_COMMAND_SETPARAMETERS (0x12) ///< Set parameters -#define PN532_COMMAND_SAMCONFIGURATION (0x14) ///< SAM configuration -#define PN532_COMMAND_POWERDOWN (0x16) ///< Power down -#define PN532_COMMAND_RFCONFIGURATION (0x32) ///< RF config -#define PN532_COMMAND_RFREGULATIONTEST (0x58) ///< RF regulation test -#define PN532_COMMAND_INJUMPFORDEP (0x56) ///< Jump for DEP -#define PN532_COMMAND_INJUMPFORPSL (0x46) ///< Jump for PSL -#define PN532_COMMAND_INLISTPASSIVETARGET (0x4A) ///< List passive target -#define PN532_COMMAND_INATR (0x50) ///< ATR -#define PN532_COMMAND_INPSL (0x4E) ///< PSL -#define PN532_COMMAND_INDATAEXCHANGE (0x40) ///< Data exchange -#define PN532_COMMAND_INCOMMUNICATETHRU (0x42) ///< Communicate through -#define PN532_COMMAND_INDESELECT (0x44) ///< Deselect -#define PN532_COMMAND_INRELEASE (0x52) ///< Release -#define PN532_COMMAND_INSELECT (0x54) ///< Select -#define PN532_COMMAND_INAUTOPOLL (0x60) ///< Auto poll -#define PN532_COMMAND_TGINITASTARGET (0x8C) ///< Init as target -#define PN532_COMMAND_TGSETGENERALBYTES (0x92) ///< Set general bytes -#define PN532_COMMAND_TGGETDATA (0x86) ///< Get data -#define PN532_COMMAND_TGSETDATA (0x8E) ///< Set data -#define PN532_COMMAND_TGSETMETADATA (0x94) ///< Set metadata -#define PN532_COMMAND_TGGETINITIATORCOMMAND (0x88) ///< Get initiator command -#define PN532_COMMAND_TGRESPONSETOINITIATOR (0x90) ///< Response to initiator -#define PN532_COMMAND_TGGETTARGETSTATUS (0x8A) ///< Get target status - -#define PN532_RESPONSE_INDATAEXCHANGE (0x41) ///< Data exchange -#define PN532_RESPONSE_INLISTPASSIVETARGET (0x4B) ///< List passive target - -#define PN532_WAKEUP (0x55) ///< Wake - -#define PN532_SPI_STATREAD (0x02) ///< Stat read -#define PN532_SPI_DATAWRITE (0x01) ///< Data write -#define PN532_SPI_DATAREAD (0x03) ///< Data read -#define PN532_SPI_READY (0x01) ///< Ready - -// My fucking clone board for some goddamn reason uses the address 0x28 -//#define PN532_I2C_ADDRESS (0x48 >> 1) ///< Default I2C address -#define PN532_I2C_ADDRESS (0x28) -#define PN532_I2C_READBIT (0x01) ///< Read bit -#define PN532_I2C_BUSY (0x00) ///< Busy -#define PN532_I2C_READY (0x01) ///< Ready -#define PN532_I2C_READYTIMEOUT (20) ///< Ready timeout - -#define PN532_MIFARE_ISO14443A (0x00) ///< MiFare - -// Mifare Commands -#define MIFARE_CMD_AUTH_A (0x60) ///< Auth A -#define MIFARE_CMD_AUTH_B (0x61) ///< Auth B -#define MIFARE_CMD_READ (0x30) ///< Read -#define MIFARE_CMD_WRITE (0xA0) ///< Write -#define MIFARE_CMD_TRANSFER (0xB0) ///< Transfer -#define MIFARE_CMD_DECREMENT (0xC0) ///< Decrement -#define MIFARE_CMD_INCREMENT (0xC1) ///< Increment -#define MIFARE_CMD_STORE (0xC2) ///< Store -#define MIFARE_ULTRALIGHT_CMD_WRITE (0xA2) ///< Write (MiFare Ultralight) - -// Prefixes for NDEF Records (to identify record type) -#define NDEF_URIPREFIX_NONE (0x00) ///< No prefix -#define NDEF_URIPREFIX_HTTP_WWWDOT (0x01) ///< HTTP www. prefix -#define NDEF_URIPREFIX_HTTPS_WWWDOT (0x02) ///< HTTPS www. prefix -#define NDEF_URIPREFIX_HTTP (0x03) ///< HTTP prefix -#define NDEF_URIPREFIX_HTTPS (0x04) ///< HTTPS prefix -#define NDEF_URIPREFIX_TEL (0x05) ///< Tel prefix -#define NDEF_URIPREFIX_MAILTO (0x06) ///< Mailto prefix -#define NDEF_URIPREFIX_FTP_ANONAT (0x07) ///< FTP -#define NDEF_URIPREFIX_FTP_FTPDOT (0x08) ///< FTP dot -#define NDEF_URIPREFIX_FTPS (0x09) ///< FTPS -#define NDEF_URIPREFIX_SFTP (0x0A) ///< SFTP -#define NDEF_URIPREFIX_SMB (0x0B) ///< SMB -#define NDEF_URIPREFIX_NFS (0x0C) ///< NFS -#define NDEF_URIPREFIX_FTP (0x0D) ///< FTP -#define NDEF_URIPREFIX_DAV (0x0E) ///< DAV -#define NDEF_URIPREFIX_NEWS (0x0F) ///< NEWS -#define NDEF_URIPREFIX_TELNET (0x10) ///< Telnet prefix -#define NDEF_URIPREFIX_IMAP (0x11) ///< IMAP prefix -#define NDEF_URIPREFIX_RTSP (0x12) ///< RTSP -#define NDEF_URIPREFIX_URN (0x13) ///< URN -#define NDEF_URIPREFIX_POP (0x14) ///< POP -#define NDEF_URIPREFIX_SIP (0x15) ///< SIP -#define NDEF_URIPREFIX_SIPS (0x16) ///< SIPS -#define NDEF_URIPREFIX_TFTP (0x17) ///< TFPT -#define NDEF_URIPREFIX_BTSPP (0x18) ///< BTSPP -#define NDEF_URIPREFIX_BTL2CAP (0x19) ///< BTL2CAP -#define NDEF_URIPREFIX_BTGOEP (0x1A) ///< BTGOEP -#define NDEF_URIPREFIX_TCPOBEX (0x1B) ///< TCPOBEX -#define NDEF_URIPREFIX_IRDAOBEX (0x1C) ///< IRDAOBEX -#define NDEF_URIPREFIX_FILE (0x1D) ///< File -#define NDEF_URIPREFIX_URN_EPC_ID (0x1E) ///< URN EPC ID -#define NDEF_URIPREFIX_URN_EPC_TAG (0x1F) ///< URN EPC tag -#define NDEF_URIPREFIX_URN_EPC_PAT (0x20) ///< URN EPC pat -#define NDEF_URIPREFIX_URN_EPC_RAW (0x21) ///< URN EPC raw -#define NDEF_URIPREFIX_URN_EPC (0x22) ///< URN EPC -#define NDEF_URIPREFIX_URN_NFC (0x23) ///< URN NFC - -#define PN532_GPIO_VALIDATIONBIT (0x80) ///< GPIO validation bit -#define PN532_GPIO_P30 (0) ///< GPIO 30 -#define PN532_GPIO_P31 (1) ///< GPIO 31 -#define PN532_GPIO_P32 (2) ///< GPIO 32 -#define PN532_GPIO_P33 (3) ///< GPIO 33 -#define PN532_GPIO_P34 (4) ///< GPIO 34 -#define PN532_GPIO_P35 (5) ///< GPIO 35 - -/** - * @brief Class for working with Adafruit PN532 NFC/RFID breakout boards. - */ -class Adafruit_PN532 { -public: - Adafruit_PN532(uint8_t clk, uint8_t miso, uint8_t mosi, - uint8_t ss); // Software SPI - Adafruit_PN532(uint8_t ss, SPIClass *theSPI = &SPI); // Hardware SPI - Adafruit_PN532(uint8_t irq, uint8_t reset, - TwoWire *theWire = &Wire); // Hardware I2C - Adafruit_PN532(uint8_t reset, HardwareSerial *theSer); // Hardware UART - bool begin(void); - - void reset(void); - void wakeup(void); - - // Generic PN532 functions - bool SAMConfig(void); - uint32_t getFirmwareVersion(void); - bool sendCommandCheckAck(uint8_t *cmd, uint8_t cmdlen, - uint16_t timeout = 100); - bool writeGPIO(uint8_t pinstate); - uint8_t readGPIO(void); - bool setPassiveActivationRetries(uint8_t maxRetries); - - // ISO14443A functions - bool readPassiveTargetID( - uint8_t cardbaudrate, uint8_t *uid, uint8_t *uidLength, - uint16_t timeout = 0); // timeout 0 means no timeout - will block forever. - bool startPassiveTargetIDDetection(uint8_t cardbaudrate); - bool readDetectedPassiveTargetID(uint8_t *uid, uint8_t *uidLength); - bool inDataExchange(uint8_t *send, uint8_t sendLength, uint8_t *response, - uint8_t *responseLength); - bool inListPassiveTarget(); - uint8_t AsTarget(); - uint8_t getDataTarget(uint8_t *cmd, uint8_t *cmdlen); - uint8_t setDataTarget(uint8_t *cmd, uint8_t cmdlen); - - // Mifare Classic functions - bool mifareclassic_IsFirstBlock(uint32_t uiBlock); - bool mifareclassic_IsTrailerBlock(uint32_t uiBlock); - uint8_t mifareclassic_AuthenticateBlock(uint8_t *uid, uint8_t uidLen, - uint32_t blockNumber, - uint8_t keyNumber, uint8_t *keyData); - uint8_t mifareclassic_ReadDataBlock(uint8_t blockNumber, uint8_t *data); - uint8_t mifareclassic_WriteDataBlock(uint8_t blockNumber, uint8_t *data); - uint8_t mifareclassic_FormatNDEF(void); - uint8_t mifareclassic_WriteNDEFURI(uint8_t sectorNumber, - uint8_t uriIdentifier, const char *url); - - // Mifare Ultralight functions - uint8_t mifareultralight_ReadPage(uint8_t page, uint8_t *buffer); - uint8_t mifareultralight_WritePage(uint8_t page, uint8_t *data); - - // NTAG2xx functions - uint8_t ntag2xx_ReadPage(uint8_t page, uint8_t *buffer); - uint8_t ntag2xx_WritePage(uint8_t page, uint8_t *data); - uint8_t ntag2xx_WriteNDEFURI(uint8_t uriIdentifier, char *url, - uint8_t dataLen); - - // Help functions to display formatted text - static void PrintHex(const byte *data, const uint32_t numBytes); - static void PrintHexChar(const byte *pbtData, const uint32_t numBytes); - -private: - int8_t _irq = -1, _reset = -1, _cs = -1; - int8_t _uid[7]; // ISO14443A uid - int8_t _uidLen; // uid len - int8_t _key[6]; // Mifare Classic key - int8_t _inListedTag; // Tg number of inlisted tag. - - // Low level communication functions that handle both SPI and I2C. - void readdata(uint8_t *buff, uint8_t n); - void writecommand(uint8_t *cmd, uint8_t cmdlen); - bool isready(); - bool waitready(uint16_t timeout); - bool readack(); - - Adafruit_SPIDevice *spi_dev = NULL; - Adafruit_I2CDevice *i2c_dev = NULL; - HardwareSerial *ser_dev = NULL; -}; - -#endif |