# Linux General/Raspberry Pi

@tableofcontents

<!-- markdownlint-disable MD031 -->
RF24 supports a variety of Linux based devices via various drivers. Some boards like RPi can utilize multiple methods
to drive the GPIO and SPI functionality.

## Potential PreConfiguration

If SPI is not already enabled, load it on boot:

```shell
sudo raspi-config
```

1. Update the tool via the menu as required
2. Select **Advanced** and **enable the SPI kernel module**
3. Update other software and libraries
   ```shell
   sudo apt-get update
   sudo apt-get upgrade
   ```

## Build Options

The default build on Raspberry Pi utilizes the included **BCM2835** driver from [the BCM2835 Library](http://www.airspayce.com/mikem/bcm2835)

1. See [the Linux section for automated installation](linux_install.md).
2. Manual install:
   ```shell
   make
   sudo make install
   ```

## Connections and Pin Configuration

Using pin 15(GPIO22) for CE, pin 24(GPIO8 commonly labeled as CE0) for CSN

Can use any available SPI BUS for CSN.

In general, use

```cpp
RF24 radio(<ce_pin>, <a>*10+<b>);
```

for proper constructor to address the correct spi device at /dev/spidev\<a\>.\<b\>

Choose any GPIO output pin for radio CE pin.

> [!WARNING]
> The pin numbers may be different for certain systems.
> In this library's examples, we use the BCM pin numbers for BroadCom chips such as
> those used on all Raspberry Pi models.
>
> For Raspberry Pi clones, such as Orange Pi or Banana Pi, defer to the pin numbers described
> in their corresponding documentation/manual.
>
> Hint: If libgpiod is installed (not required for this library),
> then you can use the included
> [CLI tools shipped with libgpiod](https://libgpiod.readthedocs.io/en/latest/gpio_tools.html)
> to gleam system-specific details.

### Linux kernel (SPIDEV driver) and the GPIO chip number

This RF24 library, as of v1.4.9, uses the Linux kernel's Character Device API to interface
with GPIO pins (AKA "lines" in kernel docs). Previous versions used the deprecated "sys fs" interface.

By default, this library attempts to use pins exposed via `/dev/gpiochip0`.
Some systems have multiple public-facing GPIO chips integrated (ie nVidia Jetson series).
If your system exposes the desired GPIO pins via a different chip (ie `/dev/gpiochip4`), then the
`RF24_LINUX_GPIO_CHIP` can be set to the correct value when compiling the library.

```shell
cmake .. -DRF24_LINUX_GPIO_CHIP="/dev/gpiochip4"
```

### General

```cpp
RF24 radio(22, 0);
```

### MRAA Constructor

```cpp
RF24 radio(15, 0);
```

See [the MRAA documentation for Raspberry Pi support](http://iotdk.intel.com/docs/master/mraa/rasppi.html)

### SPI_DEV Constructor

```cpp
RF24 radio(22, 0);
```

See [the Raspberry Pi documentation about the GPIO pins](https://www.raspberrypi.com/documentation/computers/os.html#gpio-and-the-40-pin-header)

### Pins

| PIN | NRF24L01 | RPI        | RPi -P1 Connector |
| --- | -------- | ---------- | ----------------- |
| 1   | GND      | rpi-gnd    | (25)              |
| 2   | VCC      | rpi-3v3    | (17)              |
| 3   | CE       | rpi-gpio22 | (15)              |
| 4   | CSN      | rpi-gpio8  | (24)              |
| 5   | SCK      | rpi-sclk   | (23)              |
| 6   | MOSI     | rpi-mosi   | (19)              |
| 7   | MISO     | rpi-miso   | (21)              |
| 8   | IRQ      | -          | -                 |

## brief history of RF24 library lineage

Based on the arduino lib from [J. Coliz](maniacbug@ymail.com),
the library was berryfied by [Purinda Gunasekara](purinda@gmail.com)
then forked from github [stanleyseow/RF24](https://github.com/stanleyseow/RF24) to [jscrane/RF24-rpi](https://github.com/jscrane/RF24-rpi)

Network lib also based on [farconada/RF24Network](https://github.com/farconada/RF24Network)